Dr-power TPH-184CHP Manual do Utilizador

CHIPPER/SHREDDER Operating & Assembly Instruction Manual Model: Tractor Attachment Chipper/Shredder TPH-184CHP

SECTION II - ASSEMBLY & INSTALLATION PACKAGE CONTENTS SKID POLY BAG BOLT BAG PART # WHERE USED SHREDDER/CHIPPER OWNER’S MANUAL 1 EA

STEP III – ATTACHING THE SHREDDER HOPPER • To attach the shredder hopper, push the four vibration dampeners (item #28) up into the mount holes on the

INSTALLATION • Many tractors permit direct mounting to the lower support pins on the frame of the shredder/chipper. If the lower hitch arms on you

Round off all edges. • Shorten the guard tubes to the same length. • Grease the shaft tubes and reassemble. REFER TO THE BROCHURE THAT C

SECTION III - OPERATION THIS TRACTOR SHREDDER/CHIPPER ATTACHMENT HAS BEEN DESIGNED TO OPERATE ON CATEGORY 1 TRACTORS. THIS MACHINE IS DESIGNED TO O

SECTION IV – SHREDDING & CHIPPING THIS SHREDDER/CHIPPER WAS DESIGNED FOR SHREDDING LEAFY GARDEN OR ORGANIC MATERIAL AND CHIPPING LIMBS OR BRANCHE

• When chipping branches, sometimes a tail will be left at the end of a branch. To avoid this, rotate the branch as it is fed into the chute. • Rot

USING THE CHIPPER HOPPER • This chipper-hopper is mounted on the side of the machine and is designed to chip the larger, heavier materials that the s

USE COMMON SENSE WHEN USING YOUR SHREDDER/CHIPPER. • LEARN TO RECOGNIZE THE CHANGE IN THE SOUND OF YOUR MACHINE WHEN IT IS OVERLOADED. • BECOME FA

SECTION V - MAINTENANCE AND STORAGE IMPORTANT: The knife should be checked for sharpness and the bolts attaching them to the flywheel for tightness

SECTION I – SAFETY This symbol points out important safety instructions, which if not followed, could endanger the personal safety and/or property o

REMOVAL, SHARPENING AND RE-INSTALLATION OF CHIPPER KNIFE HOW TO REMOVE THE KNIFE • Stop the tractor engine and disengage the P.T.O. driveshaft. •

• The knife should never be sharpened to the extent that more than 3/32” is taken off this measurement. • Once this measurement is below 7/32” (see

AFTER ANY BLADE OR WEAR PLATE MAINTENANCE OR ADJUSTMENT, ROTATE THE CHIPPER DISK BY HAND. WATCH AND LISTEN CAREFULLY FOR ANY UNUSUAL NOISES, CLICKING

TROUBLESHOOTING Symptom Problem Correction Belt burns. Rotor won’t turn. Rotor is jammed or stopped. A. Immediately stop engine. B. Disconnect

PARTS LIST ITEM # PART # QTY DESCRIPTION 1 090-0462 4 5/16-18 X 3/4" CARRIAGE BOLT 2 913-0380 1 CHIPPER HOPPER KIT 3 911-003

PARTS LIST 40 900-0040 1 COVER PLATE 41 913-0302 1 SPRING MOUNT BRACKET 42 090-0411 1 1/4-20 X 2-1/2" EYE BOLT 43 030-0329 1 SPRING 44

MAKE CERTAIN THAT ALL SAFETY LABELS ON THIS EQUIPMENT ARE KEPT CLEAN AND IN GOOD CONDITION. IF YOU NEED REPLACEMENT LABELS, ORDER BY PART NUMBER.

911-0150 BASIC MACHINE ITEM # PART # QTY. DESCRIPTION 1 911-0064 1 ROTOR ASSY W/HAMMERS 2 911-0152 1 CHIPPER SIDE PLATE WLDMNT 3 911-0268

COUNTRY HOME PRODUCTS Megis Road, P.O. Box 25, Vergennes, Vermont 05491 1(800) DR-OWNER (376-9637) 32

091-0044 091-0055 091-0057 091-0062 091-0059 4

091-0064 091-0088 091-0380 091-0381 5

091-0385 091-0442 091-0445 6

SAFE OPERATION PRACTICES TRAINING • Read this owner’s manual carefully in its entirety before attempting to assemble this machine. Read, underst

• Repair or replace any damaged parts before restarting and operating the machine. • If the machine should start to vibrate abnormally, immediately

MAINTENANCE AND STORAGE • Keep machine, attachments and accessories in safe working condition. • Check hardware at frequent intervals for proper t